Portable demo units: digital twins, CTIC demo unit
Mobile infrastructure, made up of 8 virtual reality units with digital twins in the Industri4 Lab demo unit and Well-being and Active Ageing Laboratory.
Quantum computing simulation infrastructure [ISAAC]
Infrastructure for the execution of quantum computing simulations, which allows the emulation of general-purpose quantum algorithms that can be used for any type of problem within the quantum context.
Multi-copter platform with LiDAR + RGB + thermal sensors
DJI Matrice 600 pro drone. Wingspan 167 cm, weight 12 kg, range 15 min, speed 65 km/h. Carbon fibre material.
LiDAR Sensor
Scout model, with Velodyne VLP-16 laser sensor. 120-metre detection range, with the capacity to take 600,000 measurements per second in the doublereturn mode.
Dimensional metrology, 3D digitalisation and reverse engineering laboratory
3D digitalisation and coordinate measuring equipment based on contact and contactless technologies (laser triangulation, conoscopic holography, structured light, etc.)
Hybrid micro-grid
Singular infrastructure for the validation of systems connected to the grid.
5G Laboratory
5G laboratory equipped with measuring, simulation and connectivity instruments, with a private 5G network simulator in FR1.
Mechanical and laser prototyping system to manufacture Microwave circuits and antennas
Mechanical and laser prototyping system with adjustable rpms and high
accuracy levels, using planar printed technology when manufacturing antennas
and microwave circuits.
Additive manufacturing laboratory for millimetre and thz waveband components
Equipment featuring two high-resolution 3D printers, sputtering machine,
sintering furnace, spin-coater and ultrasound bath.
Collaborative robotics laboratory
Collaborative robotic arms. Integration with material transportation systems and
supported by vision technologies
Software tools based on simulating discrete events.
Software tools based on simulating discrete events.
Sonic and ultrasonic sensors for materials
Sonic technology equipment oriented to its implementation in the industrial process for the resistant classification of wood and other materials.
Dedicated calculus servers
3 dedicated calculus servers
Industrial electronics laboratory
Fully-equipped Industrial Electronics laboratory, used to develop products adapted to needs of Industry 4.0.
WIRE-BONDING probe and soldering station for microwave circuits
Probe station adapted to take measurements in terahertz wavebands, featuring
a structuring laser system.
IoT sensor network
135 sensors: conductivity, water volume and floor temperature, weather
variables, dendometric sensors, humidity and leaf temperature sensors.
Additive manufacturing laboratory
Additive manufacturing equipment, using COTS and proprietary FFF technology.
Antenna and electromagnetic image measuring system
It features an anechoic chamber (8m x 5m x 4.5m) with a spherical measuring
range within the 40 GHz UHF bandwidth with a flat measuring range for
antennas within the 400 MHz – 40 GHz,
Central control system
Control system used to control the entire infrastructure, made up of a virtualised
server and real-time communications system.
Simulation and monitoring servers
Servers used to carry out simulation and monitoring tasks, which are the base of
most of the applications developed for companies.
Smart Meter Network
Smart meter network, connected via PLC and installed on different nodes of the
micro-grid.
Multi-spectral Platform for RTK fixed wing drones with RGB, NIR, RE, multispectral and/or thermal sensor
RTK Fixed wing drone with a weight of less than 2 kg. 150-g payload.
40-minute range with standard camera.
Vector radar signal generator
Vector signal generator with a 250 KHz to 44 GHz frequency range, used to
conduct studies in controlled areas and experiments in real environments with
commercial radars.
Circuit measurement and characterisation equipment
Circuit measurement and characterisation equipment, from RF and microwave
circuits to sub-millimetre measuring equipment in the radio-frequency,
microwave and sub-millimetre bandwidths, including signal generators,
spectrum analysers, vector analysers, converters, modulators, etc.
Li-ion battery management system
BMS-9 battery management system developed in collaboration with CEGASA to
control the Li-on battery modules.
Autonomous IoT monitoring stations
18 autonomous monitoring stations, which can be configured for a wide range of sensors. Remote communications with own servers.
Demo system for the technologies of industry 4.0, for yield sensor systems used in agriculture
Demo system for yield sensor systems used in agriculture (TRL3-4), in which
different technologies of Industry 4,.0 are tested (robotics, artificial vision,
sensors, data analysis, etc.).
KUKA robotised cell
Robotic cell consisting of a KUKA KR500 robot with 7 degrees of freedom
and a payload capacity of up to 500 kg.
IoT platform, in compliance with W3C standards of the web of things for data interoperability (WoTo)
Set of sensors and autonomous monitoring stations, in compliance with W3C
international standards, for data interoperability.
EOS P395
Selective laser sintering machine, designed to achieve the cost-effective
production of small and individual series and products with complex geometries.
WAAM (Wire arc additive manufacturing)
This unit is made up of a fused filament head, laser system, robot and table
with an atmosphere control system and control system. (2 robots) for robotised
welding, different offline programming applications (works with any robot brand)
and robot communication applications (remote control) and robot cell simulation
software.
KERN EVO units
Micro-machining unit with high-speed chip removal systems, achieving the
highest possible accuracy levels, within microns.
MarkTwo unit
3D printing unit that uses nylon, onyx (fibreglass reinforced nylon), Kevlar, carbon
fibre, fibreglass or HSHT (High Strength High Temperature) fibreglass.
Lithoz Cerafab 8500
Ceramic 3D printing, using LCM technology based on the photopolymerisation
principle.
Neotech-AMT 15X G3
3d printing electronics
Bio-printing equipment, 3d health
3D bio-printing units, used for the customised manufacturing of thermoplastic
polymers, hydrogel, ink, fluid foodstuffs, UV curing materials and Newtonian
fluids. Own development.
EOS M280
3D industrial printer that uses sintered metal, using direct laser techniques for
metals (titanium, aluminium, steel, cobalt-chromium, etc.).
EOS M270
Laser sintering machine to produce toolkits, inserts, part prototypes and final
products, directly from metal (titanium, aluminium, steel, cobalt-chrome, etc.).
Objet Connex 500
3D printing unit used to manufacture photopolymer resin, in rigid materials
and for rubber, and for different applications, such as prototyping and proof of
concept tests.
EOS P100
Selective laser sintering machine with polymers, designed to achieve the costeffective
production of small and individual series and products with complex
geometries.